dwarf fortress bridge defence retracting vs raised

#Dwarf fortress bridge defence retracting vs raised install

They'll need to touch in the middle so there is a continuous walking surface. To cross this large gap, we're going to need to build at least two bridges. =One Long Gap too wide for a single Bridge to Cross:= In this example I have two different scenarios: Pulling the Levers again drops the Bridges back to their lowered positions.

The South Raising Bridge becomes a 1x1 Wall.

The East Raising Bridge becomes a 1x4 North/South Wall.

The West Raising Bridge becomes a 1x2 North/South Wall.

The North Raising Bridge becomes a 3x1 East/West Wall.

Notice that the Bridge has now formed a solid 1z Level High Wall in its Raised Position. When we pull the Levers, each Bridge will raise in the Direction in which it was created. Let's hook each of these Bridges up to their own Lever Pressing (w, a, d, or x) changes the direction a bridge raises =C) Building one of the Four Directional Raising Bridges:īring up the Bridge Building Menu by pressing (b -> g). The resulting wall is always one z-level tall, watertight, and invulnerable to building destroyers.Īs the bridge 'raises', it will fling anything on the bridge into the air, with unpleasant if not always deadly side effects.Ī Raising Bridge can be built to raise in any of the four cardinal directions of the compass: North, South, East, or West. When activated by a Lever or Pressure Plate, a Raising Bridge will form a wall of its length or width in the direction it is raised. I also dropped my Hunter in the Moat, who thankfully was able to swim to safety. Notice how the bridge vanishes on the first pull and then reappears on the second. Now I'll hook up a Lever to the Bridge and give it a Pull. The moat is now freely traversable thanks to the bridge across it. Here I build a 3x7 Retracting Obsidian Block Bridge All green variations in this video are valid Bridges that can be constructed here. The rest of the Bridge can extend partly over the gap or completely across.

When buliding any type of Bridge, at least one side (the side that has walking access to your building materials) has to either be on land or right next to land. Up on the surface, I have a small 1z Level Moat guarding my entrance. =B) Building a Retracting Bridge Over a Moat: I'll pull the Levers again and the Bridges Reappear.

Watch what happens when I pull these Levers.the Bridges Disappear!

For more information about hooking Bridges up to Levers, check out this Guide.

Now I'll quickly hook each of these up to a Lever and a 1x10 Retracting Bridge from Metal Bars and a 2x4 Retracting Bridge from Wooden Logs. To change the length of the bridge in the North/South direction:Īny combination of East/West and North/South Lengths (1x1 -> 10x10) can be used to customize the size of a Bridgeįor this example, I will build a 5x3 Retracting Bridge from Obsidian Blocks. To change the length of the bridge in the East/West direction: To change the bridge back to Retract Mode, press (s) Press (w, a, d, or x) to change the direction a bridge raises ( see Raised Bridges section). =A) The Basics of Building a Retracting Bridge:īring up the Bridge Building Menu by pressing (b -> g)īy default, the bridge will be in 'Retract Mode.' When activated by a Lever or Pressure Plate, a Retracting Bridges essentially disappears.Īs the Bridge Retracts, anything on the Bridge (friend, for, or object) will be tossed or dropped onto whatever is beneath it.

the longer it will take to be designed by an Architect and then constructed by the skill labor based on the material selectedīridges can be used to dispose of unwanted items, liquids, or enemies.

the more materials it will take to build.

The Larger the Bridge you want to build is:

Wood - Blocks or Logs (built using Carpentry)īridges require a Dwarf with the Architecture skill enabled to be constructedīridges can be built in a variety of shapes from 1x1 to 10x10 and all variations in between.

Metal - Blocks or Bars (built using Any Metalsmithing).

Stone - Blocks or Boulders (built using Masonry).

You can also (q -> ctrl+shift+n) to Name your Levers.

Press (enter) after you have typed in your name.

(Shift+n) and move your cursor over your lever.

For more detailed information about bridges, check out the Wiki PagesĪs you Build your Levers and Bridges, don't forget to make MapNotes for them:.

Kitfox Discord #modding-discussion channelīronzemurder and Oilfurnace (illustrated)īuilding Bridges and Atom Smashers: A Guide by Mechanixm

#Dwarf fortress bridge defence retracting vs raised install

A three step guide:ĭownload DF Classic or install the premium version from Steam or Itch.ioįollow the quickstart guide on the wiki, or see other learning resources (below)Īsk any questions in the ☼Bi-weekly DF Questions Thread☼ - it's always active See the reasons for our rules here, and please report any problems!ĭF can be intimidating, but we're dedicated to helping new players. Want to start playing? Read this sidebar!